YOUR PLUMBING CRASH COURSE: A GUIDE TO INSTALLING A BATHTUB

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Your Plumbing Crash Course: A Guide to Installing a Bathtub

Blog Article

Check This Out

The content down below on the subject of How to Install a Bathtub Yourself is seriously attention-grabbing. You should read it.


Installing A Bathtub
Setting up a tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the job can relocate speedily; if you need to open a wall to eliminate the old tub and also place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and fit attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your restroom if you have actually already purchased a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools and material list must comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Installment


    To start with, the sustaining framework supplied with the bathroom should be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to prevent stress on the tub.
    Fit the flexible tap ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final position.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be quite troublesome because of the restricted gain access to that is typically the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
    Before moving on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

    Setting up the Bathtub


    Utilizing the two wooden boards under its feet, put the tub in the required placement. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
    The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub until the level reviews level.
    To mount faucets, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
    Switch on the water as well as examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the tub and additionally examine the overflow outlet as well as the normal electrical outlet for leakages.
    Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub must wait up until the bathtub has been used a minimum of when as this will certainly settle it right into its final placement.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in place between the tap and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, causing the water to pass through the wall in between the bathroom and the tiling, leading to complications with dampness and also possible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealer can split relatively very early if you do not consider this movement prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    I'm very occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you appreciated our blog entry. So long as you enjoyed reading our blog post if you please be sure to share it. Many thanks for your time. Visit us again soon.


    This Resource

    Report this page